Bulldog Security 721 Manual de instrucciones descargar pdf (Pagina 4)

PRECAUTIONS

MAKING CONNECTIONS

1. Strip back two inches of insulation on the wire from the remote 

starter.

Two Inches of Bare Wire

To operate your test probe, connect the black clip to a good

chassis ground. Connect the red clip to a good 12V positive source.

If the test probe is connected correctly, both the green and the

red lights will be dimly illuminated. If a positive source is

probed, the red light will glow bright and the green light will

go out. If a negative source is probed, the green light will glow

bright and the red light will go out.

USING YOUR TEST PROBE

3. Separate the vehicle wire(s) as shown. Make the separation large

enough to fit the other wire through.

2. Strip back one inch of insulation on the wire you need to connect

to.

One Inch of Bare Wire

VEHICLES WITH FACTORY

ANTI-THEFT SYSTEMS (CONT.)

ManufacturerMake/ Year Anti-theft

SIERRA 98+ PASSLOCK 2 

SONOMA 98+ PASSLOCK 2 

SUBURBAN 98+ PASSLOCK 2 

YUKON 98+ PASSLOCK 2 

YUKON XL 2000+ PASSLOCK 2 

HONDA ACCORD 98+ TRANSPONDER 

ODYSSEY 98+ TRANSPONDER 

PRELUDE 98+ TRANSPONDER 

S2000 TRANSPONDER 

INIFINITY I30 98+ TRANSPONDER 

Q45 98+ TRANSPONDER 

QX4 98+ TRANSPONDER 

JAGUAR ALL 98+ TRANSPONDER 

JEEP GRAND CHEROKEE 99+ TRANSPONDER

(GREY KEY ONLY)

WRANGLER 99+ TRANSPONDER

(GREY KEY ONLY)

LEXUS  ALL 97+ TRANSPONDER 

LINCOLN CONTINENTAL 97+ TRANSPONDER 

LS 2000+ TRANSPONDER

LINCOLN  MARK V3 97+ TRANSPONDER 

NAVIGATOR 97+ TRANSPONDER 

TOWN CAR 97+ TRANSPONDER 

MERCEDES ALL 97+ TRANSPONDER 

MERCURY COUGAR 99+ TRANSPONDER 

MOUNTAINEER 98+ TRANSPONDER

(Some)

MYSTIQUE 97+ TRANSPONDER

(Some)

SABLE 96+ TRANSPONDER 

NISSAN MAXIMA 98+ TRANSPONDER 

OLDSMOBILE ACHIEVA 95+ PASSLOCK 1 

ALERO 99+ PASSLOCK 2 

AURORA 95+ VATS 

BRAVADA 98+ PASSLOCK 2 

CUTLASS 97+ PASSLOCK 2 

NINETY-EIGHT  VATS 

SILHOUETTE 99+ TRANSPONDER

DO NOT use mechanical wiring connections, such as crimp or snap

together taps. Follow instructions on page 6-8.

DO NOT disconnect the battery if the vehicle has an anti-theft-coded

radio or is equipped with an airbag. Doing so may cause a warning

light to be displayed and may require a trip to the dealer to be

corrected.

DO NOT leave the interior or exterior lights on for an extended period

of time as it may cause battery drain. Remove the dome light fuse

from the fuse box. NOTE: Starter systems do not work well with a

partially discharged battery.

DO NOT mount the control module until all connections have been

made and tested. Using wire ties or double sided tape, MOUNT THE

MODULE UNDER THE DASH.

PLEASE USE CAUTION: DO NOT CUT, PROBE OR DISCONNECT 

THE VEHICLE’S AIRBAG WIRES. THESE WIRES WILL ALMOST 

ALWAYS BE INSIDE A BRIGHT YELLOW TUBE LOCATED NEAR 

THE STEERING COLUMN HARNESS.

WARNING!

GENERAL MOTORS REAR WHEEL DRIVE VEHICLES AND DODGE DAKOTAS

All General Motors rear wheel drive vehicles and Dodge Dakotas

built prior to 1996 do not have an electrical Neutral Safety

switch. They have a mechanical neutral safety switch. The mechanical

neutral safety switch operates as follows.

a)The key will only turn to start position when the gear selector 

is in park or neutral.

b)The key can only be removed from the ignition switch when the 

gear selector is in the park position.

You must use special precautions with this system. For more

information see page 13.

1 2 3 4 5 6 7 8 9 10

Comentarios a estos manuales

Sin comentarios

Bulldog Security 721 Manual de instrucciones Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bulldog Security 721